General Administration

Last updated: March 23rd, 2021

Cloud Networking provides centralized management, visibility, and control without the cost and complexity of controller appliances or overlay management software. ReadyLinks products are built from the ground up for cloud management, and come out of the box with centralized management, layer 7 device and application visibility, real-time web-based diagnostics, monitoring, reporting, and more.
Quickstart Guide Installation Guide Port and VLAN Configuration Layer 3 Switching Configuration Templates

Features

  • Managed via ReadyView dashboard
  • Automatic firmware upgrades
  • SNMP/Syslog integration
  • IPv4 ACL support
  • DHCP Snooping
  • 802.1X Authentication
  • 10/100/1000 Mbps RJ45
  • 2x 10G SFP+ ports
  • IGMP Snooping
  • VectorBoost
  • VLAN models
  • Phoneline or Coax

Models

GL-12xT-P600D GL-24xT-P600D GL-12xC-P600D GL-24xC-P600D GL-12xB-P600D GL-24xB-P600D
Cable medium Twisted pair Twisted pair Coax Coax Coax Coax
ReadyLink Ports 12 (RJ45) 24 (RJ45) 12 (F) 24 (F) 12 (BNC) 24 (BNC)
1GbE RJ45 2 2 2 2 2 2
10GbE SFP+ 2 2 2 2 2 2
PoE/PoE+ 12 24 12 24 12 24
PoE++ 4 4 4 4 4 4
Configuration

The basic initial configuration of the GLx is just as simple as any other model of ReadyLinks switch. The links below provide additional information and instructions relating to each step in getting the device setup and configured for the first time. 

![BASE]
configure terminal
management mode readyview
readyview password-connect username readyview password readyview
readyview password-connect filenumber 1 username readyview password readyview
end
![VLAN_INTERFACE]
configure terminal
interface vlan 1
ip address dhcp
end
end
![SNTP]
configure terminal
sntp client server-address time.google.com response-time 3 zone-offset GMT0 time-offset 0
end

  1. Claim the device to your Organization in the ReadyView Dashboard
  2. Add the device to a Network
  3. Physically connect the device to the local network
  4. Allow the device to complete check-in and perform any initial firmware upgrades
  5. Finish configuring the device from the ReadyView Dashboard

Hardware

GL-12xT-P600D GL-24xT-P600D GL-12xC-P600D GL-24xC-P600D GL-12xB-P600D GL-24xB-P600D
ReadyLinks Ports 12 (RJ45) 24 (RJ45) 12 (F) 24 (F) 12 (BNC) 24 (BNC)
1GbE RJ45 2 2 2 2 2 2
10GbE SFP+ 2 2 2 2 2 2
BNC Sync In/Out In/Out In/Out In/Out In/Out In/Out
USB Type C / RJ45 Console 1 1 1 1 1 1

Physical

Throughput and capabilities

GL-12xT-P600D GL-24xT-P600D GL-12xC-P600D GL-24xC-P600D GL-12xB-P600D GL-24xB-P600D
PoE/PoE+/PoE++ Capable Yes, 600W Yes, 600W Yes, 600W Yes, 600W Yes, 600W Yes, 600W
Switching Capacity 128 Gbps 128 Gbps 128 Gbps 128 Gbps 128 Gbps 128 Gbps
AC Power Supply Option Redundant (600W max) Redundant (600W max) Redundant (600W max) Redundant (600W max) Redundant (600W max) Redundant (600W max)
DC Power Supply Option 44-54VDC / 3-15A (In/Out power stacking) 44-54VDC / 3-15A (In/Out power stacking) 44-54VDC / 3-15A (In/Out power stacking) 44-54VDC / 3-15A (In/Out power stacking) 44-54VDC / 3-15A (In/Out power stacking) 44-54VDC / 3-15A (In/Out power stacking)
Power Stacking Stack up to 4 units for 2,160W of dynamic PoE+, PoE++ budget Stack up to 4 units for 2,160W of dynamic PoE+, PoE++ budget Stack up to 4 units for 2,160W of dynamic PoE+, PoE++ budget Stack up to 4 units for 2,160W of dynamic PoE+, PoE++ budget Stack up to 4 units for 2,160W of dynamic PoE+, PoE++ budget Stack up to 4 units for 2,160W of dynamic PoE+, PoE++ budget

Common Troubleshooting

My device won't connect to the ReadyView dashboard.

Confirm the device is on and connected to the Internet.


My device won't connect to the ReadyView dashboard.

Confirm the device is on and connected to the Internet.


My device won't connect to the ReadyView dashboard.

Confirm the device is on and connected to the Internet.

LEDs

The GLx switch uses LEDs to inform the user of the device's status. While the device powers on, all the LEDs will flash indicating the device is booting up, additional details below.